S020 Fluorescent tube lamp
|Luminous flux:||3800 lm, 7000 lm, 10000 lm, 14000 lm|
|Consumption:||48 W, 78 W, 108 W, 160 W|
|Length:||635 mm, 935 mm, 1235 mm, 1535 mm|
|Supply voltage:||230 VAC +-20%|
|Ambient temperature:||-20 to +50°C|
|Fluorescent tube lifetime:||20 000 h|
|Ballast lifetime:||50 000 h|
We provide volume discounts from 11 pcs, 101 pcs
Choose a variant
|S020 24WX2/230R||gland on right side||plastic clips|
|S020 39WX2/230R||gland on right side||plastic clips|
|S020 54WX2/230R||gland on right side||plastic clips|
Specifications - S020 Fluorescent tube lamp
S020 fluorescent tube lamps are especially suitable for even lighting in larger areas. The fluorescent tube lamp of the S020 series consists of an extruded aluminum profile with plastic fronts, in which two T5 fluorescent tubes, a polished aluminum reflector, and electronic ballast are placed.
The profile is sealed with a polyurethane seal that withstands all known lubricating and cutting fluids. The front of the tube lamp is covered with 4 mm thick tempered glass with exceptional resistance to breakage. Both side faces of the machine light are equipped with threads for the M20x1.5 gland, so it is possible to choose the mounting of the gland on the left (L), on the right (R), or for the through the supply (LR). The connection terminal is hidden under the gland.
|Fluorescent tubes||Luminous flux||Consumption||Length|
|2 x 24 W||3800 lm||53 W||635 mm|
|2 x 39 W||7000 lm||87 W||935 mm|
|2 x 54 W||10 000 lm||120 W||1235 mm|
|2 x 80 W||14 000 lm||178 W||1535 mm|
FLUORESCENT TUBE LAMP CONNECTION:
One face of the fluorescent tube lamp (or both faces in the case of the through power supply) is fitted with an M20x1.5 gland. The connection terminal is accessible after unscrewing the gland, sealed with an "O" ring. This makes connecting the tube machine lamp to the power supply very quick and easy and does not require the disassembly of the lamp's sealing elements.
FLUORESCENT TUBE LAMP INSTALLATION:
The fluorescent tube machine lamp is attached to the machine as standard with plastic clips inserted into the notch on the bottom of the lamp. The clamps have a hole with a diameter of 5.1 mm and after mounting on the lamp, the spacing of these holes is 142.5 mm. In the standard version, 4 pieces of these clips are included as part of the delivery. On request, the machine lamp can be equipped with two articulated joint fixtures with the possibility of rotation in the range of +10 -60 degrees.
1) Mount the machine light so that the cable gland is located at the lowest point.
2) The passage of the supply cable through the panel on which the machine light is mounted should be lower than the gland of the lamp.
3) If you use a cable with a metal braid, terminate the braid in front of the gland, apply a shrink tube over the end of the braid, and insert only the center of the cable with the shrink tube into the gland. The metal braid would spill water into the machine lamp despite the very well-tightened gland.
The aluminum profile allows excellent heat dissipation, thus preventing a reduction in life and efficiency
Low tube lamp of only 31 mm
Connecting the fluorescent tube lamp to the power supply without disassembling the lamp and breaking its tightness
Flat glass has about 20 times higher resistance to breakage compared to the glass tube
The product has been added to the cart
Flood machine lights S020 Fluorescent tube lamp
The aluminum profile allows excellent heat dissipation, thus preventing a reduction in life and efficiency Low tube lamp of only 31 mm Connecting the fluorescent tube lamp to the power supply without disassembling the lamp and breaking its tightness Flat glass has about 20 times higher resistance to breakage compared to the glass tube