S020 LED Luminaire
|Supply voltage||230 VAC +-20%|
|Luminous flux:||3150 lm, 4200 lm, 8600 lm, 10400 lm|
|Consumption:||18 W, 23 W, 48 W, 60 W|
|Luminary length:||635 mm, 935 mm, 1235 mm, 1535 mm|
|Light source:||LED tubes T5, 175 lm/W|
|Minimal lifetime:||50 000 h|
|Ambient temperature:||-20 to +50°C|
We provide volume discounts from 11 pcs, 101 pcs
Choose a variant
|S020 LED 18W/R||gland on right side||plastic clips|
|S020 LED 23W/R||gland on right side||plastic clips|
|S020 LED 48W/R||gland on right side||plastic clips|
Specifications - S020 LED Luminaire
These luminaires are especially suitable for even lighting of larger areas. The S020 LED luminaires follow the proven S020 series luminaires, but are equipped with highly efficient LED tubes. Their consumption dropped to 1/3 at the same luminous flux, the lifespan was extended to 50,000 hours and the price remains the same. The luminaires of the S020 LED series consist of an extruded aluminum profile with plastic fronts, in which two T5 LED tubes are located. The profile is sealed with a polyurethane seal that withstands all known lubricating and cutting fluids. The front of the luminaire is covered with 4 mm thick tempered glass with exceptional breakage resistance. Both side faces of the luminaire are equipped with threads for the M20x1.5 gland, so it is possible to choose the gland mounting on the left (L), on the right (R) or for the through-supply (LR) - see installation recommendations. The connection terminal is hidden under the gland.
|Luminary S020 LED||Consumption (W)||Luminous flux (lm)||Length (mm)|
|S020 LED 18W||18||3150||635|
|S020 LED 23W||23||4200||935|
|S020 LED 48 W||48||8600||1235|
|S020 LED 60 W||60||10400||1535|
One face of the luminaire (or both faces in the case of the through power supply) is fitted with an M20x1.5 gland. The connection terminal is accessible after unscrewing the gland, sealed with an "O" ring. This makes connecting the luminaire to the power supply very quick and easy and does not require disassembly of the luminaire's sealing elements.
The luminaire is attached to the machine as standard with plastic clips inserted into the notch on the bottom of the luminaire. The clamps have a hole with a diameter of 5.1 mm and after mounting on the luminaire, the spacing of these holes is 142.5 mm. In the standard version, 4 pieces of these clips are included as part of the delivery. On request, the luminaire can be equipped with two joint fixtures with the possibility of rotation in the range of +10 -60 degrees.
1) Mount the luminaire so that the cable gland is located at the lowest point.
2) The passage of the supply cable through the panel on which the luminaire is mounted should be lower than the gland of the luminaire.
3) If you use a cable with a metal braid, terminate the braid in front of the gland, apply a shrink tube over the end of the braid and insert only the center of the cable with the shrink tube into the gland. The metal braid would spill water into the luminaire despite the very well-tightened gland.
The aluminum profile allows excellent heat dissipation, thus preventing a reduction in life and efficiency
Low luminaire height of only 31 mm
Connecting the luminaire to the power supply without disassembling the luminaire and breaking its tightness
Flat glass has about 20 times higher resistance to breakage compared to the glass tube
High specific power of the light source 175 lumens/W
The product has been added to the cart
Flood machine lights S020 LED Luminaire
The aluminum profile allows excellent heat dissipation, thus preventing a reduction in life and efficiency Low luminaire height of only 31 mm Connecting the luminaire to the power supply without disassembling the luminaire and breaking its tightness Flat glass has about 20 times higher resistance to breakage compared to the glass tube High specific power of the light source 175 lumens/W